VOLKTEK NSH-9308P Manuel d'utilisateur

8-Port Gigabit Web Smart Switch NSH-9308P User Manual Version: 2.3 September 2007 1

2.1.3 Port-based VLAN Port-based VLAN is a kind of VLAN, which is a group of ports marked by same group ID, different VLAN (different ID) can’t commun

2.1.4 Tag-based VLAN Tag-based VLAN is another kind of VLAN, which is a group of ports assigned to the same VLAN ID. Different VLAN (different ID) can

1. VLAN Aware mode: Enabled - Strip VLAN tag from received frame and insert VLAN tag in transmitted frame, except ingress frames which’s VID is the

2.1.5 Port Trunking Port Trunking defines how to create a single high-speed logical link that combines several low-speed physical links. By default,

2.1.6 Port Mirroring Set the port mirroring option to monitor data being transmitted through a specific port. A default diagram is shown below. Choo

2.1.7 Quality of Service QoS (Quality of Service) refers to the mechanisms in the Switch’s network software that make the actual determinations of whi

16

2.1.8 Storm Control Set storm control limitation to prevent abnormal traffic. Choose frame types that you want to control, and select the limitation

2.1.9 LACP Different from the static port trunking, LACP provides another way to aggregate ports to a group (trunk) dynamically according to IEEE 802.

2.1.10 RSTP The Spanning-Tree Protocol (STP) is IEEE 802.1d standardized method for avoiding loops in switched networks. Enable STP to ensure that onl

TABLE OF CONTENT 1 INTRODUCTION ...

You can modify the following parameters of RSTP function to accommodate your network. System Configuration z System Priority – A value to identify

2.1.11 IGMP This switch provides IGMP snooping feature to detect IGMP queries and report packets. This feature can limit the forwarding of multicast f

2.1.12 802.1x Before you enable the 802.1x function, contact the administrator of RADIUS server to get IP address, UDP port number and secret. 22

2.1.13 PoE status and command operation PoE status definitions: Non-PD: The connected device is an Ethernet device but not a PD device. No Load: No

2.2 Monitoring 2.2.1. Port Statistics Select “Port Statistics” to display overview information of all ports. 2.2.2 Detailed Port Statistic To displ

2.2.3 LACP Status Select “LACP Status” to display information about LACP. 2.2.4 RSTP Status Select “RSTP Status” to display information about RSTP.

2.2.5 IGMP Status Select “IGMP Status” to display information about IGMP. 2.2.6 Ping Use this tool to test reach ability to a remote host. 26

2.3 Maintenance 2.3.1 Warm Reboot Reboot system remotely, without changing current configuration. 2.3.2 Factory Default Reset system configuration t

2.3.4 Config File Click “Backup” and select a device path to store configuration file. The default file name is “switch.cfg”. Click “Browse…” to se

3.0 Terminal Mode management Terminal mode is easy to operate; it is useful when in-band Ethernet communication was malfunction. No password is neede

1 Introduction The NSH-9308P Switch is a high performance web-smart managed switch, which provides up to 8 10/100/1000Mbps copper Ethernet ports. This

System Configuration [all] System Restore Default [keep IP] System Name [<name>] System Reboot System Xmodem System SNMP [enable|disable] System

Contact Information VOLKTEK CORPORATION 4F, No. 192 Lian-Cheng Road Chung-Ho, Taipei 235, Taiwan ROC TEL: +886-2-8242-1000 FAX: +886-2-8242-3333 Tec

1.1 Main Features This switch provides the following main features: z Non-blocking, line speed, store-and-forward z Support jumbo frame, Max. pack

1.2 Start to Manage This Switch User can start to manage this switch by ether web mode through Ethernet port or terminal mode through RS232 port. 1.2

2 Web management After login through Web Browser, the switch’s main management page will show up. The left part on the page provides the function me

2.1 Configurations 2.1.1 System information The system diagram shows common system information, they are H/W, F/W version, MAC address, IP address, su

because the IP address of this Switch has been changed. 2.1.1.2 Relocate HTTP port number The default port number of HTTP access is 80, but unauthoriz

2.1.2 Ports Port status page always shows current port status of all 8 ports. User can set link mode, enable or disable flow control and jumbo frame.